UV/LED Gel Nail Lamp User Guide

Gel Nail Lamp

  1. Remove the Gelous UV/LED Gel Nail Lamp and DC Adaptor from the packaging.
  2. Remove the blue film on the base plate and the clear film over the timer.
  3. Connect the DC Adaptor.
  4. Plug the DC Adaptor into a switched off power point.
  5. Switch the power point on once the DC Adaptor is plugged in. Do not remove and insert the DC Adaptor while the power point is turned on, as this could cause sparking and/or short-circuiting.
  6. After painting your nails with each coat of the Gel Nail Polish, place your hand or foot inside the UV/LED Gel Nail Lamp. Make sure your thumb and all your fingers are relatively flat, or cure your thumb and fingers separately. 
  7. Curing options:
    • 10 seconds: Press the 10S button to cure small nail art designs, such as dots or lines for 10 seconds.
    • 30 seconds: Press the 30S button to cure large nail art designs, such as flowers or checkers.
    • 60 seconds: Press the 60S button to cure regular coats of Gel Nail Polish.
    • Smart timer: Place your hand inside the lamp to start the smart-timer. This is an alternative to pressing the pre-set buttons and stays on for up to 120 seconds. 
    • Low heat mode: Press the 99S low heat mode button to cure at 12W for 50 seconds, then 24W for 49 seconds. Use for curing Builder Gel, if you have sensitive nails, or if you experience heat spikes.

Travel Gel Nail Lamp

  1. Remove the Gelous UV/LED Travel Gel Nail Lamp and USB-A to USB-C cable from the packaging.
  2. Plug the USB-C end of the cable into the Travel Gel Nail Lamp. Plug the USB-A end of the cable into a wall charger, computer port, laptop port, or power bank.
  3. After each coat of Gel Nail Polish, place your hand or foot under the Travel Gel Nail Lamp. If your thumbs do not fit under the Travel Gel Nail Lamp, cure them both separately.
  4. Curing options:

Using in Application and Removal

To find out how to use your Gel Nail Lamps in Application, follow the link below.

Using in application

Tips & Tricks

Use compatible products

Use all Gelous products (Base Coat, Colour Coat, Top Coat, and Gel Nail Lamp) to ensure compatibility.

Careful preparation

Push back your cuticles, shape & buff your nails, then dehydrate. Finish with optional pH Bond and Nail Primer for ultimate adhesion.

Apply away from sun

Apply your Gel Nail Polish away from sunlight and your Gel Nail Lamp when turned on to avoid it curing on the brush.

Apply thinly

Apply your Gel Nail Polish in thin, even coats, leaving a gap between the Gel Nail Polish & cuticle to prevent lifting.

Avoid skin contact

Remove any Gel Nail Polish on your skin before curing to prevent reactions or allergies.

Use a strengthener

Use Builder Gel or Rubber Base Coat if your nails are weak or flaky.

Cap your coats

Cap every coat of Gel Nail Polish by running the brush horizontally over the free edge of your nail.

Practice aftercare

Avoid washing dishes or using cleaning products without gloves, and use Cuticle Oil daily.

FAQ's

If you are a new user of Gel Nail Polish, please don’t be disheartened if your first few manicures don’t last as long as expected. There are many tips and tricks to applying Gel Nail Polish that make the difference between a long-lasting application and an application that doesn’t last long enough (i.e. chips easily or peels). Often, new users of Gel Nail Polish make small mistakes during the application process that cause premature chipping or peeling. Once you've mastered your Gel Polish application, you'll enjoy flawless, long-lasting manicures time and time again. Practice really does make perfect!

Please be patient, read our Application Guide carefully, and take note of our tips and tricks.

  • Always use Gelous Base Coat, Colour Coat, Top Coat, and Gel Nail Lamp together. Our Gel Nail Polish and UV/LED Gel Nail Lamp are specially formulated to be fully compatible, with the lamp emitting at 365+405nm to ensure a safe and effective cure. While this dual-wavelength setup is common, we strongly advise against mixing brands—such as using other polishes with our lamp or vice versa—as they may not be properly compatible. Incompatibility can result in under-curing, which may lead to poor wear or even cause damage to your nails or skin.
  • Ensure you address weak nails. If your nails are naturally weak or bend easily, Gel Nail Polish may not hold properly and can crack or lift. Start by applying a layer of Rubber Base Coat to add flexibility and help the Gel Polish adhere. If additional strength is needed, apply one or two thin coats of Builder Gel. As your nails grow longer, you can also build an apex with Builder Gel to improve structure and enhance durability.
  • Nail prep is very important and will directly influence the longevity of your mani or pedi. Without it, your Gel Polish may not adhere properly, leading to premature lifting or chipping. Apply Cuticle Remover to help loosen any overgrown cuticle and the eponychium—the small strip of skin that can sit on the nail near the base. Gently push it back with a Cuticle Pusher, or Orangewood Cuticle Stick. Trim your nails, then take your time to gently buff the nail surface using the fine side of the Nail File, removing any shine. 
  • Make sure to clean your nails thoroughly after buffing, as any residual buffing dust, oil or other contaminants will reduce adhesion of the gel and affect the longevity. Brush away buffing dust with the Dust Brush, then clean your nails by applying Gel Nail Polish Remover to a Lint Free Wipe, or using a Pure Acetone Wipe to thoroughly clean the surface of your nails. Pay attention to the area under your nails and around the cuticles. This removes dust and oils while dehydrating the nail bed, giving the Base Coat a clean surface to adhere to.
  • Apply pH Bond to dehydrate the nail plate, followed by a thin layer of Nail Primer to ensure maximum adhesion.
  • Don’t apply your coats of Gel Nail Polish too thick and make sure they are an even thickness. Pay attention to the cuticles and the sides, as this is where Gel Polish can get thicker if you have too much Gel Nail Polish on the brush. To achieve a thin application, remove excess Gel Nail Polish from the brush by circling it around the inside of the bottle neck, pressing it off.
  • Cap every coat of Gel Nail Polish by running the brush horizontally over the free edge of your nail. View capping diagram here. If you have shorter nails, start each coat by using a Nail Art Brush or the tip of your bottle brush to cap the free edge.
  • When applying, start in the middle of the nail then ‘push’ the Gel Nail Polish gently towards the cuticle without it touching. It is important to leave a thin gap between the edge of the Gel Nail Polish and your cuticle when applying. If the Gel Nail Polish is applied to the cuticle, it can separate and lift as your nail plate grows. Aim to avoid getting any Gel Nail Polish on your skin or cuticle, however if you do, remove it with an Nail Polish Remover Pen, Orangewood Cuticle Stick, Nail Art Brush or Silicone Tool before curing. 
  • In terms of aftercare, avoid washing dishes or using cleaning products without gloves, use Cuticle Oil regularly to help your nails looking fresh for longer. If you get a snag, file this down so it does not catch and cause further damage.

You can find our full list of FAQ's here.

See the links below to find our YouTube tutorials.

Watch tutorials

Find out more